6.35x32快断 UL 陶瓷管保险丝 额定电流：100mA-30A 额定电压：125V/250V

6.35x32陶瓷管快断保险丝-------UL CSA

1.规格型号和安规认证
MODEL  NUMBER  AND  SAFETY  CERTIFICATION
品名规格：系列号+额定电流+额定电压+认证符号
   Model  Number:  Part  Number+Rated Current+Rated Voltage+Approvals.
例子[example]:
6CFU       20A      250V                    1)系列号  Part  Number
                                                      2)额定电流  Rated  Current
1）           2）       3）                     3)额定电压  Rated  Voltage
1-2 额定电流和额定电压
Rated Current  And  Voltage
额定电流： 63mA~40A
Rated Current: 63mA~40A
额定电压：125V/250V AC
Rated  Voltage:125V/250V AC
1-3标示Marking
保险丝上需有下列标示
The fuse shall have the following marking:
规格：特性符号+额定电流+额定电压
Specification:Characteristic  Symbol+Rated Voltage
   63mA~800mA : _mA250V    1A~40A:_A250V
Trade mark:The Manufacture’s Logo+Part Number+Approvals  
 
63mA~40A: 
 
注意：对标示字样大小没有规定
Note:Size of the markings have not be specified.
2.适用范围
SCOPE
适用於一般电子设备。Used in electronic equipment.
3.工程图和结构
OUTLINE DRAWING AND STRUCTURE
3-1 工程图（单位：mm）
Outline Drawing and Dimensions(Unit:mm)
 
            

         

3-2结构
Structure
编号
No.	元件
Component	材质
Material	数量
Quantity
(1)	熔丝
Wire	合金
Alloy	1
(2)	铜帽
Cap	黄铜镀镍
Brass with mickel plated	2
(3)	本体
Body	陶瓷管
CERAMIC Tube	1
(4)	引线
Lead	镀锡铜线
Tinned Copper wire	2
(5)	砂
Sand	石英砂
Quartz sand	1  
4.外观及形状
APPEARANCES AND CONFIGURATION
4-1外观：不应有破碎、明显的污斑
Appearances:There shall no fragmentation and of remarkable blotch.
4-2形状：带脚的保险丝
Configuration:Axial Leaded Fuse.
 
5.物理特性
PHYSICAL CHARACTERISTIC
5-1 拉力测试
Tensile test
沿端子的轴向施加10N的拉力，持续1分钟。
Keep pulling the cap of the fuse with 10N at axial direction for 1 min.
 
6.电气特性
ELECTRICAL CHARACTERISTICS
熔断/电流特性：
Pre-Arcing Time/Current Characteristic
 
a、Breaking capacity（分断能力）(Time Lag and Fast Acting)
10000A	125V	AC
35A	250V	AC (less or 1A)
100A	250V	AC (1.1A—25A)
400A	250V	AC (25A—40A) b、Electrical characteristics
Fast Acting(参照美标)
Rated current	**	135%	200%	250%
63mA~40A	Mini	Max.	Max.	Max.(40A)
4 hours,	1 hour	30 sec	30 sec c、Temperature character
When ** of rating the temperature rise doesn’t exceed 75℃.
d、Approvals
Amp Code	Ampere
Rating (A)	Voltage
Rating
(V)	Nominal Cold
Resistance
(Ohms)	Nominal
Melting
I2t (A2 sec)	Agency Approvals
UL	CSA
6CFU-.375	0.375	250	0.820	0.050	x	x
6CFU-.500	0.5	250	0.500	0.115	x	x
6CFU-.750	0.75	250	0.250	0.466	x	x
6CFU-001.	1	250	0.189	0.690	x	x
6CFU-002.	2	250	0.0700	11.0	x	x
6CFU-003.	3	250	0.0432	14.6	x	x
6CFU-004.	4	250	0.0470	10.4	x	x
6CFU-005.	5	250	0.0300	26.0	x	x
6CFU-006.	6	250	0.0240	45.0	x	x
6CFU-007.	7	250	0.0187	71.0	x	x
6CFU-008.	8	250	0.0153	105	x	x
6CFU-010.	10	250	0.0105	206	x	x
6CFU-012.	12	250	0.00760	570	x	x
6CFU-015.	15	250	0.00505	292	x	x
6CFU-020.	20	250	0.00355	631	x	x
6CFU-025.	25	250	0.00235	1450	x	x
6CFU-030.	30	250	0.00182	2490	x	x
6CFU-040.	40	250	0.0014	22925	x	x


7.环境特性
 ENVIRONMENTAL SPECIFICATION
7-1 操作温度范围：-5℃~60℃
Operating Temperature: -5℃~60℃
7-2 保存条件
Storage Conditions
温度：+10℃~60℃
Temperature: +10℃~60℃
在相对湿度≤75%下平均可存放3年
On average, It can be stored below the relative humidity or 75% for 3 years.
在非露天下，相对湿度为95%下较多可存放30天。
Without dew, It can be kept under humidity of 95% for 30 days.
 
8.焊接条件
SOLDERING PAAMETERS
8-1波峰焊
Wave Solder
焊接温度：260±5℃
Soldering Temperature:260±5℃
焊接时间：4 Sec. Max.
Soldering Time:4 Sec.Max.
8-2手工焊锡
Manual Solder
焊接温度：350±5℃
Soldering Temperature: 350±5℃
焊接时间：3 Sec. Max.
Soldering Time: 3 Sec. Max.
 
9.其他使用注意事项
OTHER NOTICE IN USING
如果需在保险丝上加热缩套管，烘烤温度与时间需参照以下规定
If heat shrink tubing was needed,the roast temperature and time should be refer to the following.
设定烘烤温度：不大於150℃  烘烤时间：50s Max.
The temperature should be sel under 150℃,roast time:50s Max.